If you want to know how to use a ring keypad, you need to have proper knowledge of what each light and buttons stand for. The ring keypad comes in handy as it gives you control of your Ring Alarm. The ring alarm keypad has many features which make it easy to install and use. It can be mounted on a wall or placed on a table near a door that you often use.
Its battery takes a few hours to charge by connecting it to a power supply using a USB power cable. The internal rechargeable battery can last up to 7 months depending on how you use it.
Whenever you trigger your ring alarm, the ring alarm keypad often acts as a second siren that sounds. A duress code can be set to disarm the alarm and get an emergency response. Whenever a sensor is triggered you would hear chirp tones, if it is enabled in the app under the keypad device page.
With that being said we would take a look at how to use a ring keypad 1st and 2nd generations in this article.
How To Use a Ring keypad
The steps below explain how to use a ring keypad 1st generation.
- Press the checkmark and x buttons to trigger the panic alarm. They will sound the siren and get a police emergency response.
- You bypass sensors when you press the checkmark button.
- It has an adjustable volume for chirps and announcements.
On how to use ring keypad Keypad here is an additional specification of ring keypad 2nd generation:
- Press and hold the Emergency buttons for 3 seconds to get Police, Fire, and Medical response.
- It has new keypad buttons and LEDs that help to provide visual and tactical cues.
- It is smaller with an improved design that makes it easier to mount and use.
2nd Gen Ring Keypad
You can arm and disarm the ring keypad (2nd generation) without using a smartphone. We would now describe and explain the buttons and lights on the ring keypad.
The Network light is lit during pairing or when it indicates an error. If a red light is displayed it means there is a network communication failure.
Recommended: How Long Does it Take to Charge a Ring Doorbell?
Battery Light
The battery light shows battery status, when it is off it means there is enough battery power. when yellow is displayed the battery is low, a red light means the battery is very low and when charging it blinks a green light.
Police/Panic Button
When you press the police/panic button it sounds like a siren and also sends notifications to emergency contacts. If you enrolled in professional monitoring, a panic signal would be sent to the monitoring centre to request police dispatch.
Fire Button
When you press the Fire button, it sounds like a siren and sends notifications to emergency contacts. If you enrolled in professional monitoring, a panic signal would be sent to the monitoring center to request a fire department dispatch.
Medical Button
When you press the medical button base station will flash and a notification would be sent out. If you have enrolled in professional monitoring, a panic signal to request medical / ambulance dispatch would be sent to the monitoring center.
Motion Sensor
The motion sensor helps to detect motion around the Keypad when power save mode is off.
Disarmed Mode
You can enter your access code and click the disarmed mode button to disarm your Alarm system when you get home.
Home Mode
In-home mode, enter your access code and click on it to arm your Alarm system. You should also use it to secure your home at night.
Away Mode
Enter your access code and click on away to arm your alarm system when you are not at home.
Light Bar
The light bar shows the remaining time during entry and exit delays.
Ring Keypad Gen 1 Keypads
Understanding what action each light stands for and how the buttons on the ring keypad perform would determine how to use ring keypad Gen 1. Now let’s take you through how to use the ring alarm keypad Gen 1 buttons:
Network Connection Light
The network connection light shows when the is an error connecting to the base station.
Battery Light
The battery light shows the current charge status and the battery level.
Faulted Sensor
It allows you to know if one of your sensors has been tampered with or faulty when you try to arm the ring keypad alarm.
Disarm Mode Button
Enter your code with a keypad and click the disarm button when you want to disarm your alarm system.
Away Mode Button
Enter your access code with a keypad and click to arm away button to alarm your system.
Home Mode Button
Enter your access code with a keypad and click the home button to place your alarm system in armed home mode.
Checkmark Button
The checkmark button is used to bypass aby sensors that can’t be armed and to continue arming the system. If you press and hold the checkmark button and the x button for 3 seconds, this will trigger the panic alarm.
X Button
The x button is used to cancel any attempt to enter a code, and also for triggering the Panic alarm.
Ring Keypad Not Working
Try the following troubleshooting if you find yourself in a situation where your ring keypad isn’t working.
Unplug Keypad
If your ring keypad is not working unplug the keypad from the power outlet and move the keypad closer to the Base Station.
Check Power Outlet
If the power outlet is defective, ensure you plug your ring keypad into a good power outlet. Test the power outlet using a multimeter for continuity, if found to be damaged ensure you plug your ring keypad into another power outlet.
Reset Your Ring Keypad
Tap the pinhole reset button with a pinhole tool or use a paper clip to reset your ring keypad.
Factory Reset Your Ring Keypad
If you are still faced with your ring keypad not working after trying all the steps above, you should factory reset your ring keypad. You should know that when you factory reset your ring keypad your device will be reset to its default settings. Your ring keypad settings such as chirps and volume adjustments will be removed.
To factory reset your ring Keypad: Press and hold the pinhole reset button in the back of the Keypad for 10 seconds, until it flashes red.
Update Your Keypad Firmware
If your ring keypad is not working, the software may require to be updated. The software of your ring alarm system needs to be updated to improve the performance and stability of your alarm system.
Sometimes you need to update the firmware of your ring alarm system. During an update, your home would remain secure and will only begin when your ring alarm gets disarmed. Follow these steps to update your ring keypad firmware:
- First, unplug your keypad and plug it back.
- Open the Ring app.
- Open the menu >> Devices, and click the alarm base station.
- On the alarm device list, click the blue status bar at the bottom of the screen.
- Then click any Keypads with device updates available.
- Click schedule update and follow the directions.
Can I Leave The Ring Keypad Plugged in?
You can decide to leave the ring keypad plugged into a USB power supply cable. It takes a few hours to charge the internal rechargeable battery. The battery should last up to 7 months depending on whether it is being used.
What is Disarm Button on Ring Keypad?
The disarm mode button helps to disarm your Alarm system when you get home. Enter your access code and press the disarm button to disarm your Alarm system.
How Do I Change The Code on My Ring Keypad?
Whenever you are working with an alarm system your 4-digit access code is the most important information you will need to use often. An access code is a unique 4-digit number that is assigned to an individual. You must enter your access code and press either the Home button, Away button, or disarm button to change modes using the Keypad.
Follow these steps to change or reset an access code on your ring keypad:
- Go to the Ring App, Open the menu. Ensure you are in the right location, then click Settings.
- Click Shared Access.
- Click on the User you want to change.
- Click Reset Access Code. Enter a four-digit code, and re-enter the code.
- Then click Done and click Save.