Encountering the issue of the Whirlpool washer not draining during a wash cycle can be pretty annoying, as it would most probably delay your laundry time, making you spend longer than necessary.
The Whirlpool washer is known to be reliable because it develops almost little to no fault, but one of the commonly reported issues with the washer is the issue of the Whirlpool washer not draining.
Different reasons can cause the issue of the Whirlpool washer not draining, and this article will be looking at them, along with the troubleshooting solutions you can use to resolve it.
Why is the Whirlpool Washer Not Draining
Several reasons might be the cause of the Whirlpool washer not draining issue, and some of the commonly reported reasons are listed below.
- The wrong wash cycle was selected.
- The drain hose is kinked or clogged.
- The drain pump is defective.
- The Whirlpool washer door lock is malfunctioning.
- The lid switch assembly is malfunctioning.
The solutions to these various issues that can potentially cause the Whirlpool washer not draining issue will be discussed in the next section of the article.
You can also learn How to fix Whirlpool Dishwasher Not Draining
How to Fix Whirlpool Washer Not Draining
The solution to fix the Whirlpool washer not draining depends on the cause of the washer not draining.
This section of the article will explain the different available troubleshooting methods you can use to fix the Whirlpool Washer not draining.
Check the Wash Cycle Selection
The spinning speed of the washing machine solely depends on the cycle you selected at the beginning of the wash cycle.
The delicate fabric settings will typically spin slower than the setting for washing heavy clothes, so if you set the delicate fabric settings to wash heavy clothes, the washer will not spin sufficiently, and you will still have wet clothes at the end of the cycle.
Check the drain hose.
The drain hose allows wastewater to be removed from the washer, and if it is clogged, the washer will be unable to drain waste water away, ultimately resulting in the issue of the Whirlpool washer not draining.
You can follow the instructions below to check if the drain hose is clogged or kinked.
- Ensure that the washer is turned off and disconnected from its power source.
- Then gently disconnect the hose from the washer, preparing for the possibility of water spillage.
- Now drain any wastewater in the hose into an empty bowl or bucket.
- Then remove every debris and other obstructions in the hose using a tweezer or a straightened wire hanger.
- However, if you notice that the blockage in the hose cannot be reached or removed, then the best bet is to replace the hose.
If you have either cleared the hose of the debris in it or replaced it with a new one, you can attempt a wash cycle with the washer to confirm that you have resolved the issue of the Whirlpool washer not draining.
Check the Washer Door Lock
The front loader models of the Whirlpool washing machine have washer door locks that secure the door of the washer when locked and alert the washer to either spin or drain.
If the washer door lock is defective, it would be unable to notify the washer to begin draining.
Check that it is not an item that is obstructing the washer door lock and preventing it from working.
If it is an item, you should remove it, and the washer should begin draining.
If the issue is with the door lock itself, then you would need to engage the service of professionals to replace it.
Check the Drain Pump
Depending on the Whirlpool washer model, the drain pump removes wastewater from the washer via the standpipe or sink.
If the drain pump is defective, its impellers will not function, and the washer will be unable to expel water from it.
You can check if your drain pump is bad and needs replacement by following the instructions below.
- Ensure that the washer is turned off and disconnected from its power source.
- Then stick your finger in the drain outlet to feel the impellers if the pump is turning freely.
- Then turn the pump flywheel with your second hand; you will be able to feel whether one or more of them is broken.
- You may also notice broken plastic bits at the base of the pump housing.
If you notice that the pump is not turning freely either because of the broken flywheel or broken plastic at the bottom of the pump housing, you would need to engage a professional to replace the pump.
Check the Lid Switch Assembly
The top loader models of the Whirlpool washer have a lid switch that will stop the washer from spinning, draining, or performing any other activity while open.
If the Lid switch malfunctions, the washer will not get the signal necessary to drain water.
You can use a multimeter to check the lid switch for continuity, and if there is no continuity, you have to seek the help of a professional to fix it.
Where is the Whirlpool Washer Drain Filter Location
The drain filter is an essential part of the washer that prevents debris from flowing from the drain pump down to prevent clogging the pump.
If you use a Whirlpool washer top loader and want to locate the drain filter, you can follow the instructions below.
- Turn off the washer and disconnect it from its power supply.
- Then check for the filter on the valves in the top loader.
- Water entering and exiting the pump and hoses is usually sieved with the aid of the valve filters.
- Then under the agitator, at the base of the wash basket, you will find two plastic lint filters with fine mesh in the form of crescents.
- The water pushes the lint off the bottom of the filters and down the drain as it spins and drains.
The top loader’s drain filter is designed so that it does not require cleaning or replacement.
If you use the Whirpool washer duet, you can locate the drain filter by following the instructions below.
- Turn off the washer and unplug it from its power outlet.
- Then remove the access panel from the washer by pulling the bottom of the panel close to you.
- The Whirlpool Duet’s filter is located under the front kick plate.
- Lint shed from clothing while washing is collected in the washer filter.
Since the filter in the Whirlpool duet stores lint, the filter should be cleaned with water at least once in 6 months to prevent it from getting clogged.
How to Fix Whirlpool Washer Not Draining Top Load
If you use the top loader model of the whirlpool washer, you can resolve the issue of the Whirlpool washer not draining by following the instructions below.
- Disconnect the washer from the power supply for about 3 minutes, then plug it back and start the wash cycle after at least 30 seconds.
- Confirm that the drain hose is not clogged; attempt to clean or replace it if it is.
- Check that the drain pump is not defective, and get a professional to replace it if it is defective.
- Check the lid switch assembly, and replace it if defective.
Conclusion:
This article has explained in detail the possible reasons behind the Whirlpool washer not draining issue and possible solutions.
If you have tried the troubleshooting methods in this article with no success, it is recommended that you seek further assistance from a professional.