Is the “door locked” indicator on your Whirlpool washer also flashing a light? Relax! This is one of the common problems with whirlpool washers and it can be easily fixed. You don’t have to replace your Whirlpool washer too quickly. This article will show you why Whirlpool washer’s door is locked and flashing light as well.
Thanks to an automatic door-locking function that stops the door from opening during a cycle, you will never have to worry about your washing machine flooding your house or trapping items inside. The door may, however, lock due to malfunctions either before the cycle even begins or in the middle of it.
You might want to run a diagnostic test on your washer if you are not sure why the door is locked and the light is flashing. You are not alone if your Whirlpool washer’s door is locked and blinking light. This is a typical Whirlpool issue that is fixed easily and quickly.
Why Whirlpool Washer’s Door is Locked and Flashing Light
Before you start using your Whirlpool washer, you will notice the door light flashing if it can lock. The error demonstrates that your washer has responded normally after detecting that the door is open. The common causes and solutions for a locked whirlpool washer door flashing light are listed below:
- There’s a problem with the drain pump
- The lid switch may be faulty
- The actuator motor needs to be checked
- Damaged sensor actuator
- Faulty hose
- Faulty door switch
- Check the lock control, it may be faulty
- Faulty door latch
- There may be water in the machine tub
- Check the main control board
Once you can ascertain why the Whirlpool washer’s door is locked and flashing light, the next thing is to fix the error to make the washer functional again. 
How to fix Whirlpool Washer’s Door is Locked and flashing Light
The doors of Whirlpool washing machines are locked by a mechanism that prevents them from opening during a wash cycle. You should do this for your protection and to stop water from seeping from your appliance.
The washer door may occasionally lock and remain locked. When this occurs, one or more internal components most likely have a problem that needs to be fixed or replaced.
Follow the steps below to fix why Whirlpool washer’s door is locked and flashing light:
Fix the Faulty Drain Pump
There is a drain pump assembly facing you at the washer’s centre. Remove the pump’s knob bolt. While removing the knob, ensure to have a bucket or bowl ready to collect the water in front of the drain pump.
If the drain pump breaks down and your washer is unable to discharge the water, the door may remain locked. You can fix the faulty drain pump by following the steps below:
- If something is stuck in the drainpipe, allow high-pressure water to go through the pipe to clear out the obstruction.
- To clean the drainpipe, you can also pour a solution made from a mixture of vinegar and water into the pipe to quickly clean the whirlpool drain line.
This step should fix the why Whirlpool washer’s door is locked and flashing light questions. If not, you can proceed t the next solution below. 
Check the Lid Switch and Striker
When a washing machine door is locked and the light is flashing, one of the typical causes is a bad switch. The spinner cannot move correctly if the switch is faulty. The striker is the part that assists in pressing down the lid switch. Always ensure it’s not out of alignment.
You can fix this by:
- Inserting the screwdriver into the switch actuator’s holes.
- Make sure you replace the switch once you complete this step and the machine will continue to function normally in case the light is not blinking.
Check if the washer has unlocked and the light is no longer blinking. If it’s still locked, try out the next fix.
Check the Actuator Motor
Perhaps there is a problem with the actuator, which is caused by a broken wire connection. You can check the appliance’s wire connection as a result. The door-locked light could flash if there is damage or loss. To fix this, follow the step below:
- Turn off the breaker and open the machine wire system.
- Check if the connection is lost or doesn’t supply enough voltage.
- Ensure the wires are tightened and fix them to allow them to supply enough voltage to the machine actuator motor properly.
This step should fix the why Whirlpool washer’s door is locked and flashing light questions. If not, you can proceed t the next solution below. 
Check the Hose
Make sure there are no leaks or cracks when inspecting the condition of the inlet hoses.
The airtight hose is ideal, but even the best things eventually wear out. Check for potential kinks and damage that may have developed over time.
These might frequently be the cause of water flow issues that affect the water level sensor. Here’s how to fix a bad hose:
- Look for any kinks in the hoses that could obstruct water flow.
- Take off the washer’s hose.
- First, turn off the water supply and take the inlet hoses off using pliers.
- Put a container under the hose’s opening to collect any water that may be left over.
This step should fix the why Whirlpool washer’s door is locked and flashing light questions. If not, you can proceed t the next solution below.
Check the Lock Control
A malfunctioning lock or manipulated lock could be indicated by a light blinking in your Whirlpool washer. The mistake could be explained by the possibility that the tampered lock stops the washer door from opening until it has finished its cycle.
Before using the washer again, you must update the lid lock. After unplugging the whirlpool washer for 10 minutes, you might need to reset it. Follow the steps below:
- After 45 minutes of removing the plastic cord from the outlet, turn off the machine’s water supply.
- Lift the top cover to reveal the machine’s front, you will hear a click sound once it fully opens.
- After opening the machine lid, take out all the clothing or things from the detergent dispenser.
- When the washer’s white reset power button clicks, press it again.
- Closing the washing room doors will prevent light from entering, which could interfere with the sensor’s ability to detect blackness in the air.
- From there, how the washer operates is determined by this.
That’s it!
Check the Main Control Board
The main control board is in charge of all the functions of your washer. The system might flash a light when you close the washer door, but nothing happens.
The control panel, which governs communication between the washer and its various components, is the main culprit in this kind of issue.
However, this error might be caused by detectors receiving too much or too little voltage or by a power fault.
This also could be a result of a power surge, or the control board overheating. To fix this, follow the steps below:
- Replace the control board if the washer’s door-locked light is blinking.
- A qualified appliance technician should perform this task since they can identify the issue and replace the control board for you.
Reset your Whirlpool Washer
When a washing machine is acting up, it can be frustrating because it may seem as though nothing you do would immediately fix the issue.
Allow your washer o to be idle for at least 45 minutes by unplugging it from the wall. This will help reset your machine fixing any minor glitches it may be experiencing.
This step should fix the why Whirlpool washer’s door is locked and flashing light questions.