- Advertisement -

[Updated-Fix] Samsung Dryer not Heating

Samsung is a reliable brand when it comes to electronic devices. They have a low service ratio when you compare the units of sold product to the number of users who requested a service call. In most cases, it is usually 10% or lower for the past few years. 

Some Samsung users might prefer to DIY it by themselves while others would prefer to call a service repairer to take care of it.

Therefore, if you own a Samsung dryer and you are also stuck with your Samsung dryer not heating up, you might want to read this till the end.

In most cases, the reason why you are stuck with your Samsung dryer not heating up is usually caused by a burnt heating element or a blown-out fuse.

The question now, is how will you know what has caused your Samsung dryer not heating up and how can you fix it?

If you are keen On finding that out keep reading.

- ADVERTISEMENT -

Samsung Dryer Not Heating: Reasons and Troubleshooting Steps

Below, I will be listing the various reasons why your Samsung dryer isn’t heating up and how you can troubleshoot it. Starting from the easiest to more technical issues.

Exceeding Required Load

Exceeding required load

Before going into any technical aspect, if you are faced with your Samsung dryer not heating up. The first thing you ought to check is if the clothes you loaded into the machine have exceeded the required capacity.

Placing too much clothing at once in the dryer would hinder the heat from flowing all around the dryer causing the heat to spread unevenly.

Sometimes that might just be the problem.

How to Troubleshoot

The first thing you should do is to check the level of clothes you just placed inside the dryer. If the clothes almost reach the top, you should limit the number of clothes going into the dryer in a cycle.

- ADVERTISEMENT -

NOTE: Each Samsung dryer has a manual on the limit to how much clothing you can stuff inside the dyer. For most dryers, it is 75%. 

You should check your Dryer manual for that.

Blocked Dryer Vent

Perhaps, the well-known justification as to why your Samsung dryer might not heat up sufficiently is an impeded air vent.

The venting arrangement of the Samsung dryer permits soggy air from wet garments to escape from the machine and to the outside. An obstructed vent can cause warming issues.

Because of long use, ordinarily, the vent might become blocked. which is due to little particles stalling out inside the Lint filter and air vent.

How to Troubleshoot

Even though cleaning the lint filter greatly assists in reducing blockages. Specks of dirt can still penetrate the air vents making it hard for the moisture from the wet cloth to escape. 

This eventually affects the dryer’s efficiency.

Now, if this is the first time you are struggling with your Samsung dryer not heating up, then you might want to check the vent and clean it at least once quarterly.

Defective Heating Element

Defective heating element

- ADVERTISEMENT -

It is easy to notice if the problem you are facing is linked to the heating element since it either gives off a burnt smell or some odd sound.

Your heating element has one job. And its job is to create heat for the dryer since it works on a principle similar to that of an electric heater. Its resistance to electricity makes the heating element get hot.

How to troubleshoot

Since the heating elements can either go damaged or can cause your Samsung dryer to get too hot. This could also be caused by overloading and your best bet is to reduce any form of issue.

Also, always clean your vent to allow the hot air from escaping from the device.

Blown Thermal Fuse

Your thermal fuse has its job. Which is to protect the Dryer from overheating or from unexpected power surges. Anytime the dryer reaches an extreme temperature the fuse will trip off the device. Now, maybe your heater has stopped heating because it has tripped the system off.

To resolve this follow the steps below

How to troubleshoot

Get a multimeter and carry out a continuity test on the fuse. If it fails, the fuse has issues and needs a replacement.

NOTE: You can access the fuse by checking around the blower of the heating element.

Samsung Dryer not Heating

In most cases, the reason why you are stuck with your Samsung dryer not heating up is due to your heating element. 

Sometimes it might not be the case, but once your Samsung dryer gives off an odd sound you might have to check the heating element with a multimeter, while also checking for the vent to ensure it isn’t clogged.

Samsung dryer not Heating Reset

Samsung Dryer not Heating reset

Sometimes resetting might not be the right decision if you are faced with a technical issue. The most common reason why you might want to carry out a reset is if you are faced with error code issues. 

NOTE: ensure Resetting is applied as a last resort.

If you are struggling with similar issues, here is how to reset your Samsung dryer.

How to Reset Samsung Dryer

  • Turn Off and unplug your dryer from the wall socket
  • Be patient for 3-5 minutes while still leaving it unplugged.
  • Now, plug it back and power it ON.

If that wasn’t clear or you are looking for a more detailed step for your Samsung dryer you should check here

Samsung Dryer not Heating Control Board

Samsung Dryer not Heating control board

On your Samsung dryer, you have a control board which is used to control the heating temperature and duration. In addition to that, the control board is a very delicate part of the dryer as you do not want to fiddle with it.

If you have tried all the troubleshooting steps above and you are still experiencing an issue with your Samsung dryer not heating, you should try resetting the control board.

  • If you are unsure about how to do that, follow the steps below.
  • unplug your dryer from the wall socket
  • Be patient for 3-5 minutes while still leaving it unplugged.
  • Now, plug it back and power it ON.

If after doing this, there aren’t any positive results, you should consider replacing your control board with a new one.

Samsung Dryer Heating Element

Your Samsung heating element has one job. And it is to convert the electrical energy flowing through it into heat without the heating element. The device is just as close to useless. If you are having a heating issue with your Samsung Dyer you can simply use a multimeter to test for continuity.

If the heating element turns out to be faulty, you should replace it with a new one.

A Budget of $200 will be Ok for getting a new one including the cost of labour.

Samsung Dryer not Heating Error Code

Apart from the technical heating issue which you might face, sometime you might see error codes like HC, 1 HC, HE, and HC4. 

If you see any of these.

Resetting isn’t the next line of action. You should first verify if your vents are clogged. If they are clean, If they aren’t, clean the vents.

Samsung Dryer not Heating and Turning Off

If your Samsung Dryer isn’t heating while also turning off after a few minutes, different things could be causing this scenario.

- ADVERTISEMENT -

The first thing you should check is the heating element. If the heating element is OK, check if the fuse is blown or test for continuity with a multimeter.

If the fuse is blown, replacing the fuse again might trip it OFF. 

If you are faced with this, the most common cause of this is an overheating Dryer motor. To resolve this, you have to replace it.

If it isn’t the Dryer motor, then it is the dryer’s belt. However, if you weren’t able to resolve this issue, you should contact the Samsung support team for appropriate repairs 

Conclusion

By now, you should have figured out how to resolve your Samsung dryer not heating while also learning some technical troubleshooting steps. In addition, there are a few things you need to be aware of. if you are faced with any technical-related issues like this, be patient before you carry out a factory reset. The reason why is, factory reset clears out all the saved codes while also making it harder for a technician to perform repairs on your dryer.

Related Posts

1 thought on “[Updated-Fix] Samsung Dryer not Heating”

Leave a Comment