The Speed queen washer is popularly known to last longer when compared to other washers. So, the speed queen washer is commonly recommended by repairmen since it rarely has serious problems when compared to their washing machine models.
However, that doesn’t mean you might not come across a Speed Queen washer problem, but the majority of them are fairly easy to troubleshoot on your own unless you are not comfortable tinkering with electronic equipment.
That being said, I will be breaking down all common problems such as your Speed Queen washer not draining, Speed Queen dishwasher not starting, and other common ones that usually occur while using a Speed Queen washer.
That isn’t all, I will also explain some easy-to-do ways to resolve a Speed Queen washer problem without needing a repairman.
Common Speed Queen Washer Problems
Below are the lists of some common problems you might have faced with your Speed Queen Dishwasher coupled with various ways to troubleshoot it.
1. Overflowing Washing Machine
There are different working components in your Speed Queen dishwasher that control the amount of water that enters the washer based on the temperature and the settings you’ve specified.
However, you might experience some scenarios where the water begins to overflow more than the desired amount. If you are faced with this, there are some things you ought to do immediately.
- Firstly, power off the washer to see if the filling would stop.
- If it doesn’t then you have to look into your inlet valve or replace it if it’s damaged.
- However, if after turning your washer off, the filling steps then you might need to check your air tube that connects to the pressure switch.
- Inside the air tube, check if there is debris in the tube. If there is, try blowing it out to ensure there are no leakages in the tube.
- After sorting that out, you’ll need to replace the pressure switch since its main job is to shut off the water coming into the system when it reaches the specified quantity.
- After doing all these, check the water pressure from the housing supply and ensure it is at a minimum of 20psi.
2. Speed Queen Washer Water is Too Hot or Cold
If you are faced with your Speed Queen washer problem whereby your Speed queen water comes out too hot, or cold or probably you are faced with a scenario where the water is not coming out at all.
You should go through the steps below to troubleshoot it
- Firstly, cut off the water supply
- Take out the hoses from the machine
- Look inside both ends of the hose and see if the small screen isn’t clogged. If it is, clean it off with a brush or a toothbrush
- However, If it’s too clogged up or the screen is hard to remove, replace it
- Check the Strainer for traces of dirt, debris, or clogs, if there are no clogs. Open washer.
- Now, press down the lid switch.
WARNING: Do this cautiously, to avoid significant physical accidents since disabling the safety switch is no child joke. Do not place limbs or objects into the machine while there is a chance your machine might accidentally activate.
- That being said, feel the temperature of the water entering the machine
- If it is warm, you are good to go, however, if it is too hot or cold or it isn’t coming in, get a voltmeter to test the solenoid coils
- If the voltage is between 110-125 volts, check the wiring, however, if there is no voltage replace your valve.
- Before coupling it back, check the timer and the door lid while ensuring that none is faulty.
- If any is faulty, replace and assemble back
3. Speed Queen Washer not Filling
If you are stuck with a Speed Queen Washer problem whereby your speed queen washer is not filling. The first thing you ought to do is to check the detergent tray and also check if you have enough fabric softener in it.
That said, below are some other things you have to check out if your speed queen washer is not filling
Check the Lid
it is pretty important advice to close the lid while a cycle is going on. if you don’t, there will be little to no water inside your machine and this could affect your inlet valve, so it is important to always close the lid when running a wash cycle
Check for a Blocked Hose
If you are faced with a blocked hose issue, it could result in your speed queen washing machine not filling. So what you have to do in this case is to inspect the hose for any dirt or debris and ensure there are no tears or damages. If there are, replace the hose.
Check the Water Pressure
The speed queen washer requires at least a minimum of 20psi to fill the washer. Anything lower than that won’t work, so you should check the pressure to ensure you have at least 20psi of water pressure.
4. Speed Queen Washer Not Draining
If you are stuck with a Speed Queen Washer problem whereby your speed queen washer is not draining, the most common reason for this is the drain pump, drain system, or drain hose.
If the drain pump is faulty, the water pumped into the drain would not drain as it is supposed to. When it comes to the drain system, it could be caused by dropping an item like clothes coins, etc, into the washer causing it to block the drain system.
In addition to all that, the drain hose must also be kinked so it would not allow water to flow freely in the hose causing the water to become stagnant.
That being said, here is how you can troubleshoot these issue
- Check the Drain System for kinked hose or clogs.
- Check the lint filter if your washer has one.
- Check the side valve at the outlet for the tub.
- Most pumps are belt-driven, so it is possible your belt broke, is loosened, or the pulley which drives the pump could have sheared off.
- Size up the bearings and check if the pump is jammed up with items. If it is, check the impeller blades to ensure it is not broken. If it is, you may need to buy a new pump.
5. Speed Queen Washer Leaking
Is your Speed Queen washer is leaking? if yes, there are different sets of components in your washer that you have to check such as the drain pump, the torn tub seal, and the turn door seal. However, it is not limited to that but these issues are common reasons behind that.
That said, below are some troubleshooting steps you should take if your speed queen washer is leaking
- Check if your drain pump is backing up, if it is, it could be clogged.
- If it’s not, look at the floor with a flashlight and locate the spot where the leak is coming from.
- The common places where water leaks come from are the water valve, pump, bleach dispensers, hoses, or the tub itself.
- If the water is coming from the hoses, pump, or the water valve, then the faulty components need replacement.
- another thing you want to check is the tub seal and the door seal if any of them is torn or damaged, your best bet is to replace them
- If the tub is rotting, getting a new washing machine should be a priority.
If your washer is leaking from the bottom check here for a comprehensive guide on how to fix that.
6. Speed Queen Washer Not Spinning
If you are stuck with a Speed Queen Washer problem whereby your speed queen dishwasher not spinning. One of the most common issues for that is the Drive belt.
That said, below are some troubleshooting steps you can take to resolve it.
Inspect the Drive Belt
If the drive belt isn’t in place or it is damaged, the washer will not work properly. so you have to check the pulley and inspect the belts. If the belt is broken or damaged, your best bet is to replace it. If you can’t do that on your own you can request the services of a repairman
The Control Board is Faulty
NB: if your control board is faulty, it is best left to a professional since this is a delicate part of the washer. A faulty control board means your washer start button will be faulty
If your control board is faulty the start button on your washing machine won’t work so you’ll need to inspect your washer for any burnt components and make the appropriate replacement.
7 . Speed Queen Washer Stops Mid Cycle
If you are stuck with a Speed Queen Washer problem whereby your Speed Queen washer stop in the middle of a wash cycle, you don’t need to fret as the issue can easily be resolved by going through the steps listed below.
Your Door is not Correctly Latched
While your laundry is going through a wash cycle, one of the things that can stop it from working is to open the lid, in some cases, maybe you opened the door but you didn’t latch it correctly. If that is not the case, proceed to the next step.
The Water Timer is Faulty.
In a scenario where your timer is faulty, it is very common for your cycle to stop when it hasn’t reached the desired time. if this issue persists, you might need to disassemble the machine and test for continuity using a multimeter.
If there is no continuity, the timer needs to be replaced
Why are all the lights flashing on my Speed Queen Washer?
If you are faced with this, the most likely reason for this is a low water pressure, the drain system is clogged with an irregular item or maybe the screen filter is blocked with dirt or debris.
Why is my Speed Queen Washer not working?
If your speed queen washer is not working or starting, the first thing you ought to check is the power cord. However it might not be the case, but you should first test the power cord with a multimeter for continuity. If there is no continuity, then it needs to be replaced.
Conclusion
By now, you should have figured out some speed queen washer problem and some steps you can take to resolve it. However, you need to ensure that your limit opens your lid while a cycle is going on to avoid a scenario of leaking since leaking would affect your Speed queen washer warranty.